Go Back   Train Horn Forums > Installation Help & Advice > Horn Kits
 Register

Reply
 
Thread Tools Display Modes
  #1  
Old 4 Weeks Ago
mrlarry24 mrlarry24 is offline
Newbie
 
Join Date: September 2017
Posts: 2
mrlarry24 is on a distinguished road
Default Help with relay wiring Viair 20005

Guys...

I have a Viair 20005 combo that has the pressure switch already mounted on the compressor.

I have the relay which calls for the following:

Wire to 12v constant: (I have a fused wire on battery)
Wire to 12v switched: (I have to underhood fuse box, switched fuse)
Wire to compressor:
Wire to pressure switch:

My question is, I have the Viair relay. But since the pressure switch is already mounted on the tank, I only have 1 wire going to the compressor/pressure switch and the relay calls for 2 separate. There's nothing in the Viair manual about how to wire a relay in with this combo system.

I tried the wire on both contacts on the relay, but it doesn't kick the compressor on. When I take the wire going to the compressor and touch the battery, the compressor kicks on.

Do I only need a 3 contact relay?

Thanks for the help...I didn't realize this forum existed until today.
Reply With Quote
  #2  
Old 4 Weeks Ago
DBO's Avatar
DBO DBO is offline
Horn Addict
 
Join Date: October 2010
Location: Brisvegas
Posts: 1,236
DBO is on a distinguished road
Default Re: Help with relay wiring Viair 20005

Doesn't look like that Viair combo needs a relay (because of the small compressor). The pressure switch handles the electrical load.

You use a relay when you have a normal switch that cannot take the electrical load (i.e. amps) that's needed to be switched. In those cases the relay can be linked to your pressure switch to turn the compressor on and off.

Have a look at post #8 for details on how to wire a simple relay circuit on a kit like yours in order to make it switch on/off with a relay that is only powered on when you have your ignition key turned to the ACC position:
https://www.trainhornforums.com/show...ght=SPST+relay
__________________
Train Entertainment System:
- 2010 Suzuki Grand Vitara with Twin Viair 480C's; 200psi; Norgren regulator (R73G-4AK-RMG);Twin 1/2" lines (GW line regulated @110, SMC line @200); 5 gal.tank; K3LA on custom manifolds; SMC/VA85 solenoid; Graham White 353-100 (Install | Videos | Schematic).

The Collection:
Leslie SuperTyfon: RS5T, RSL3L
Nathan Airchime: K5LLA, K3LA
Shocker S4 XL

Last edited by DBO; 4 Weeks Ago at 10:47 PM.
Reply With Quote
  #3  
Old 4 Weeks Ago
mrlarry24 mrlarry24 is offline
Newbie
 
Join Date: September 2017
Posts: 2
mrlarry24 is on a distinguished road
Default Re: Help with relay wiring Viair 20005

Thanks much for the info!

I was reading the manual and it said they "highly recommend" using a relay, but didn't include a wiring diagram. I'm assuming because it pulls 20 amps.

My last smaller system, I just had a switch, but wanted to do this correctly.

I'll take a look at the link you sent for the relay.

Again, I appreciate the help.
Reply With Quote
  #4  
Old 4 Weeks Ago
DBO's Avatar
DBO DBO is offline
Horn Addict
 
Join Date: October 2010
Location: Brisvegas
Posts: 1,236
DBO is on a distinguished road
Default Re: Help with relay wiring Viair 20005

No worries. If you want to take the load off the pressure switch, just run the main power wire through the relay and direct to the compressor (i.e. do not run it through the pressure switch). You would then use your pressure switch on your trigger wire instead to to make the relay turn on/off.
__________________
Train Entertainment System:
- 2010 Suzuki Grand Vitara with Twin Viair 480C's; 200psi; Norgren regulator (R73G-4AK-RMG);Twin 1/2" lines (GW line regulated @110, SMC line @200); 5 gal.tank; K3LA on custom manifolds; SMC/VA85 solenoid; Graham White 353-100 (Install | Videos | Schematic).

The Collection:
Leslie SuperTyfon: RS5T, RSL3L
Nathan Airchime: K5LLA, K3LA
Shocker S4 XL
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:56 AM.